Tag Archives: sewing

T-shirt Quilt

4 Jan

T-shirt quilt

 

We had acquired about 3 zillion t-shirts over the years. While it’s impossible to wear all of these, it’s also hard to get rid of them because many are fond reminders of schools, races, and great friends. So I made a patchwork quilt.

Using a template (a coffee table book, not the best option really) I cut out the logo/design part of the t-shirt with a circular quilting blade. Then I sewed the rectangles into strips, and sewed the strips together. This is the time to use your machine- don’t bother hand quilting. Rather than using batting and backing, I just purchased a large swath of fleece and quilted the fleece and patched t-shirts together, bringing the fleece around to the front to create a border.

A Tale of Two Dresses

5 Jan

Brown Print DressOlive Green Dress

I found these two dresses at a local goodwill for $5 each. Judging from the construction details, these dresses were homemade in the 1960s. They are very similar and approximately a modern size 14 or 16. I couldn’t resist trying to make them into something wearable.

 

Cutting triangular sections from the dresses

Cutting triangular sections from the dresses

 

 

I started by cutting large, triangular sections from the bottom of both dresses.  Then I sewed the opposite print triangles into each dress.

 

Sewing the opposite print triangle into each dress.

Sewing the opposite print triangles into each dress.

 

Next, I cut a small triangle out the front neckline of each dress and reversing prints, sewed the opposite triangle into each dress.

 

 

Since I added seams, which took in the material, I had to compensate by adding a seam up the front of the dress, connecting the two triangles. This prevented bunching.

 

Seam sewn up the front of the brown dress.

Inside view of the seam sewn up the front of the brown dress.

 

 

 

 

 

 

I cut open the seam and ironed it open so it laid flat. The back seam was more tricky, because it was near the zipper. I tucked a fold and tacked the inside as best as possible.  I could have redone the entire zipper, but honestly, I’m too lazy and this dress is still pretty ugly.

At this point, the dress is still way to big for me, so I tried it on and measured how many inches I needed to remove. I greatly exaggerated the existing darts at the back of the dress and made new darts in the front.

 

enlarged darts at the back

enlarged darts at the back

 

 

Finish darts by cutting out the excess material from the darts and ironing open the seams. To finish the dress, I cut 3.5 inches of length from the sleeves and added a 0.5 inch hem. The shorter sleeves lightened up and modernized the dress.

 

Finished dress

Finished dress

 

 

 

 

 

 

 

 

 

In true freestyle fashion, I made it up as I went a problem solved along the way. The finished dress is a vast improvement over the old one, but is still pretty funky/ugly. Stay tuned for my post on completing the other dress.
back of the finished dress

back of the finished dress

 

 

Sew your own Swimmy Seatsaver

1 Nov

To make your own swimmy seatsaver, You will need two yards of vinyl fabric (like the cheap picnic table-cloth) and two yards of knit cotton or jersey.

1- Cut the fabric in half longwise. You will be able to make two seatsavers with 2 yards of fabric. Alternatively, you can buy one yard, cut it in half and stitch together the two halves to make a two yard length.

 

2- Lay out the material so the knit is right side down on the bottom, and the vinyl is right side down on top of the knit. Trim the fabric so the vinyl is approximately 2 inches smaller than the knit fabric. Fold the knit fabric excess edge in half twice so it overlaps the vinyl without folding the vinyl. Pin the edge in place every two inches on the two long sides and one of the short sides. I know pinning every two inches seems excessive and annoying, but it’s necessary.

       

3- Sew the three edges that were pinned. This is not a project to handsew! The materials are thick and tough. Sew slowly and keep a good grip on the fabric. It will want to twist, and it will shift easily. Double seam the edges for extra strength.

4- The next step is to shape the end of the seatsaver to fit your headrest. You will be cutting four triangles into the end of the fabric. The size of the triangles will be dependent on the size of you car’s head rest. Mark off the unfinished edge of your seatsaver in four portions. Use safety pins to pin the marked points together (first to second point; second to third point, etc…). 

Experiment with tucking the seams and hang the seatsaver over your car seat. Once you have a comfortable, natural fit, mark the edges of the creases/future seam. Then cut along your marks, through both layers of fabric, removing four triangles.

 

5- Match the “right’ side of the fabric back to back and pin the edges. Sew a double seam on the edge. I find it is easier to pin and sew them one at a time.

 
6- Finally, finish any rough edges around the head rest. This “clean up” is usually best done by hand.
     
All four seams are sewn
 
 

the finished product, ready for you favorite swimmer

%d bloggers like this: